• Search Catalog

Cart Summary

Shopping Cart Empty

Main >

Position/motion

Small Image
Add to Cart
Quantity On Hand: 25
The sensor has three axes of measurements, X Y Z, and pins that can be used either as I2C or SPI digital interfacing. You can set the sensitivity level to either +-2g, +-4g, +-8g or +-16g. The lower range gives more resolution for slow movements, the higher range is good for high speed tracking. Input and logic works on 3-5 V.
ID: 11851   Your Price: €4.70
Small Image
Add to Cart
Quantity On Hand: 19
This is an HMC5883L triple axis compass magnetometer sensor module with power supply of 3-5 V, measuring range ± 1.3-8 Gauss and I2C communication.
ID: 12130   Your Price: €4.90
Small Image
Add to Cart
Quantity On Hand: 37
This is an MPU6050 triple-axis gyroscope and acce​​lerometer module for Arduino with communication mode of I2C/IIC.
ID: 11075   Your Price: €6.50
Small Image
Add to Cart
Quantity On Hand: 4
The MPU-9250 combines a three-axis accelerometer, gyroscope and magnetometer supported by a 16-bit ADC and I2C/SPI interfaces. The power supply is 3-5 V, logic 3.3 V, and the measurement range is ±250, ±500, ±1000 and ±2000°/sec for the gyroscope, ±2g, ±4g, ±8g and ±16g for the accelerometer and ±4800μT for the magnetometer.
ID: 12824   Your Price: €18.90
Small Image
Add to Cart
Quantity On Hand: 58
This sensor allows you to calculate rotational speed of motor or count pulses between sensors (there is a 5 mm wide gap). In case of obstacle the digital output is HIGH, with no obstacle it's LOW. LM393 voltage comparator outputs signal to analog output pin. Working voltage is 3.3-5 V, board dimensions 32x14 mm.
ID: 12347   Your Price: €1.20
Small Image
Add to Cart
Quantity On Hand: 104
Plastic disc for optical speed encoder and TT DC motor with 3.5x5.4 mm axis, 20 slots, 26 mm diameter, 3.6 mm thickness.
ID: 12348   Your Price: €0.20
Small Image
Add to Cart
Quantity On Hand: 18
This board is based on u-Blox Neo-6M GPS module, has on-board backup battery and built-in EEPROM, works both with 3.3V and 5V logic over 9600 baud UART. Comes with small uFL ceramic antenna. Dimensions: 25x45x6 mm.
ID: 12031   Your Price: €9.20
Small Image
Add to Cart
Quantity On Hand: 1
An anemometer is a device used for measuring wind speed, and is a common weather station instrument. This well made anemometer is designed to sit outside and measure wind speed with ease.
ID: 10394   Your Price: €79.00
Small Image
Add to Cart
Quantity On Hand: 10
Brand: Seeed Studio
Water level sensor for Arduino can be used to measure the water level up to 10cm deep, with 5mm accuracy. It's corrosion resistant, communicates over I2C, has Grove connector. It comes with 20cm Grove cable, we added 30cm Grove to 4 pin female Dupont for easier use with standard Arduino boards.
ID: 11840   Your Price: €11.50
Small Image
Add to Cart
Quantity On Hand: 7
Non-contact liquid level sensor, working voltage 5V, outputs HIGH on detection, range 0-10 mm (non-metallic containers only), response time 500 ms, 34x24x6 mm with 30 cm cable and connector (brown = VCC, blue = GND, black = OUT).
ID: 12510   Your Price: €8.00
Small Image
Add to Cart
Quantity On Hand: 2
Brand: Adafruit
Measuring stretch forces isn't easy - unless you have some conductive rubber cord! This cord is 2mm diameter, and 1 meter long, made of carbon-black impregnated rubber.
ID: 10390   Your Price: €15.50